To optimize the cost and lead time, MYIR has launched MYC-Y7Z010/20-V2 CPU Module for replacement of the MYC-Y7Z010/20. The hardware is fully compatible. Please contact MYIR for any queries.
https://www.myirtech.com/list.asp?id=679
The MYC-Y7Z010/20 CPU Module is an industrial-grade System-on-Module (SoM) based on Xilinx Zynq-7000 family SoC available for either the XC7Z020 or XC7Z010 version. It has integrated the Zynq-7020 or Zynq-7010 device, 512MB DDR3 SDRAM, 4GB eMMC, 16MB quad SPI Flash, a Gigabit Ethernet PHY and external watchdog on board and provides 1.27mm 180-pin stamp-hole (Castellated-Hole) expansion interface to allow a large number of I/O signals for ARM peripherals and FPGA I/Os to be extended to your base board. The module is ready to run Linux and supports wide working temperature ranging from -40 to +85 Celsius which is ideal for industrial embedded applications.
MYC-Y7Z010/20 CPU Module
MYIR provides a development board MYD-Y7Z010/20 for evaluating the MYC-Y7Z010/20 CPU Module, which employs the MYC-Y7Z010/20 as the controller board by populating the CPU Module on its base board through 1.27mm pitch 180-pin stamp-hole (Castellated-Hole) interface. The base board has extended a rich set of peripheral interfaces including serial ports, USB Host port, three Gigabit Ethernet ports, CAN, TF card slot, JTAG, etc. One 2.54mm pitch 2 x 25-pin expansion header is on the base board to let more GPIOs available for further extension.
MYD-Y7Z010/20 Development Board
MYD-Y7Z010/20 Board in the Video
https://youtu.be/0oYo-u5y4aI
Features
Mechanical Parameters
-
Dimensions: 75mm x 50mm (10-layer design)
-
Power supply: 5V
-
Working temp.: -40~85 Celsius (industrial grade)
SoC
-
Xilinx XC7Z010-1CLG400I (Zynq-7010) / XC7Z020-1CLG400I (Zynq-7020)
- 667MHz dual-core ARM® Cortex™-A9 MPCore processor (up to 866MHz, for XC7Z010 or XC7Z020)
- Integrated Artix-7 class FPGA subsystem
with 28K logic cells, 17,600 LUTs, 80 DSP slices (for XC7Z010)
with 85K logic cells, 53,200 LUTs, 220 DSP slices (for XC7Z020)
- NEON™ & Single / Double Precision Floating Point for each processor
- Supports a Variety of Static and Dynamic Memory Interfaces
Memory
-
512MB DDR3 (2 x 256MB, 32-bit)
-
4GB eMMC
-
16MB QSPI Flash
Peripherals and Signals Routed to Pins
-
10/100/1000M Ethernet PHY (KSZ9031)
-
External watchdog
-
Three LEDs
- One red LED for power indicator
- One green LED for FPGA program done indicator
- One flashing green LED for system indicator
-
1.27mm pitch 180-pin Stamp Hole Expansion Interface brings out below signals:
- One Gigabit Ethernet
- One USB
- Two Serial ports
- Two I2C
- Two CAN BUS
- Two SPI
* Serial ports, I2C, CAN and SPI signals in PS part can be implemented through PL pins via Emio.
- Two ADC (16-channel ADC brought out through PL pins)
- One SDIO
OS Support
Other MYIR's Xilinx Products
http://www.myirtech.com/xilinxseries.asp
VECP Starter Kit (Vision Edge Computing Platform based on Zynq UltraScale+ ZU3EG MPSoC)
MYD-CZU3EG/4EV/5EV Development Board (MYC-CZU3EG/4EV/5EV CPU Module as core board)
FZ3 Card (Deep Learning Accelerator Card based on Zynq UltraScale+ ZU3EG MPSoC)
Z-turn Board Single Board Computer (based on Zynq-7010 / 7020)
Z-turn Lite Single Board Computer (based on Zynq-7007S / Zynq-7010)
MYD-C7Z010/020 Development Board (MYC-C7Z010/020 CPU Module as core board)
MYD-C7Z015 Development Board (MYC-C7Z015 CPU Module as core board)
|
Overview
