MY-CAM011B BUS Camera Module
The MY-CAM011B BUS Camera Module is released by MYIR specially for working on MYIR's ARM development boards. It is connected with the boards through 30-pin FPC connector and supports resolution up to 1632 by 1212 pixels. It is using OV2659 image sensor which is a 2MegaPixel digital camera. The module is measuring only 55mm by 32mm with small form factor, low power consumption, high performance which can be used in various products.
USD25 
Features
|
Item
|
Paramenters
|
|
Active Array Size
|
1632 x 1212
|
|
Power Supply
|
Core
|
1.5VDC ± 5%
|
|
Analog
|
2.6 ~ 3.0VDC
|
|
I/O
|
1.7V to 3.0V
|
|
Power Requirements
|
Active
|
224 mW
|
|
Standby
|
75 μA
|
|
Temperature Range
|
Operation
|
-20℃ to 70℃
|
|
Stable Image
|
0℃ to 50℃
|
|
Output Formats (8-bit)
|
- YUV422/YCbCr422
- RGB565/555
- GRB422
8-/10-bit raw RGB data
|
|
Lens size
|
1/5″
|
|
Lens chief ray angle
|
25.7°
|
|
Maximum Image Transfer Rate
|
UXGA(1600x1200)
|
15 fps
|
|
SVGA(800x600)
|
30 fps
|
|
720p(1280x720)
|
30 fps
|
|
1366x768
|
24 fps
|
|
Sensitivity
|
960mV/Lux -sec
|
|
S/N Ratio
|
36 dB
|
|
Dynamic Range
|
66 dB
|
|
Scan Mode
|
Progressive
|
|
Maximum Exposure Interval
|
1228 x tROW
|
|
Gamma Correction
|
Programmable
|
|
Pixel Size
|
1.75 μm x 1.75 μm
|
|
Dark Current
|
4mV/s at 60℃
|
|
Well Capacity
|
6.3 Ke
|
|
Fixed Pattern Noise
|
1% of VPEAK-TO-PEAK
|
|
Image Area
|
2856μm x 2121μm
|
|
Package Dimensions
|
4735μm x 4385μm
|
Signals Routed to 30-pin FPC Camera Interface
|
Pin
|
Signal
|
Description
|
|
1
|
VIN_5V
|
Power 5V
|
|
2
|
V3_3D
|
Power 3V3
|
|
3
|
V3_3D
|
Power 3V3
|
|
4
|
GND
|
Ground
|
|
5
|
I2C_SDA
|
SCCB data
|
|
6
|
I2C_SCL
|
SCCB input clock
|
|
7
|
CAM_RST
|
Reset（active low with internal pull up register）
|
|
8
|
CAM_PWRDN
|
Power down（active hige with internal pull down register）
|
|
9
|
GND
|
Ground
|
|
10
|
CAM_VSYNC
|
DVP VSYNC output
|
|
11
|
CAM_HSYNC
|
DVP HSYNC output
|
|
12
|
CAM_DAT7
|
DVP data output port 7
|
|
13
|
GND
|
Ground
|
|
14
|
XCLK
|
System input clock
|
|
15
|
GND
|
Ground
|
|
16
|
CAM_DAT6
|
DVP data output port 6
|
|
17
|
CAM_DAT5
|
DVP data output port 5
|
|
18
|
GND
|
Ground
|
|
19
|
CAM_PCLK
|
DVP PCLK output
|
|
20
|
GND
|
Ground
|
|
21
|
CAM_DAT4
|
DVP data output port 4
|
|
22
|
CAM_DAT0
|
DVP data output port 0
|
|
23
|
CAM_DAT3
|
DVP data output port 3
|
|
24
|
CAM_DAT1
|
DVP data output port 1
|
|
25
|
CAM_DAT2
|
DVP data output port 2
|
|
26
|
NC
|
No connect
|
|
27
|
NC
|
No connect
|
|
28
|
NC
|
No connect
|
|
29
|
NC
|
No connect
|
|
30
|
NC
|
No connect
|
Dimensions
Board Products Supporting List
The MY-CAM011B BUS Camera Module can support working with following MYIR's board products:
|
